Чистка сухого фильтра aFe POWER Magnum FLOW Pro DRY S
Решил продолжить вчерашнее промежуточное ТО и дополнить замену масла чисткой воздушного фильтра.
Кому интересно, небольшое инфо о фильтре:
aFe POWER Magnum FLOW Pro DRY S
Артикул — 18-03001. В длину 18 см + 2 см патрубок для хомута. Диаметр отверстия для присоединения — 3 дюйма.
Инструкция по чистке
1 вариант:
Постучать фильтром по твердой поверхности — обеспечивает до 85% первоначальной пропускной способности.
2 вариант:
Пропылесосить фильтр снаружи — обеспечивает до 96% первоначальной пропускной способности.
Первый раз использовал первый вариант ))) и продувку сжатым воздухом изнутри.
3 вариант:
Промывка фильтра водой изнутри. В случае сильного загрязнения можно добавить обычного мыла. Высушить в течение нескольких часов — обеспечивает до 100% первоначальной пропускной способности.
После первой чистки накатал 8000 км. Мыл с мылом. На удивление, вода после мойки была почти чистая. Попробовал быстро высушить промышленным феном, но это не дало ощутимого результата. Оставил сушиться на ночь. Утром фильтр был полностью сухой.
aFe Power Magnum FORCE Instruction Manual
aFe Power Magnum FORCE ® advanced FLOW engineering Magnum FORCE Stage-2 Air Intake System Instruction Manual P/N: 51-12642-1B / 54-12642-1B / 52-12642-1H Make: Ford Model: F-150 Year: 2015-2021 Engine: V6-2.7L (tt) EcoBoost Make: Ford Model: F-150 Year: 2015-2016 Engine: V6-3.5L (tt) EcoBoost (CARB exempt 15-16 under D-550-28 only)
aFe Power Magnum FORCE Page 13 5 Step 19: Reconnect the vent fitting. It will snap over without having to release the plastic clip. Pull up slightly to confirm installation. Step 20: Installation is complete. Any codes can be cleared with a code reader or by disconnecting the battery. You will lose any radio presets with battery disconnection. If removal of the vent insert is r
aFe Power Magnum FORCE Page 9 (These procedures should be done with the inlet tubes installed on the engine. It is shown off the vehicle for better illustration.) Step 15: Locate the o.e. plastic tube feeding the driver’s side turbo inlet. aFepower.com Refer to Figure F for Step 15 Figure F INSTALL Vent insert installation:
aFe Power Magnum FORCE ® Refer to Figure A for steps 1-4 Step 1: Disconnect the Manifold Air Pressure (MAP) sensor plug from stock airbox. 1 Step 2: Loosen the OE intake clamps using an 8mm nut driver from the left and right side runners. 2 Step 3: Unclamp the top portion of the OE airbox. 3 Step 4: Remove the OE intake and the top portion of the OE airbox by pulling straight up and out of the
aFepower.com Refer to Figure D for steps 8-9 Step 8: Remove the MAP sensor from the OE intake 1/4 turn counter-clockwise. Step 9: Install the MAP sensor on the rear aFe intake tube using the provided grommet. The grommet can be held inside the tube to give support while inserting. Figure D Page 7 INSTALL
advanced FLOW engineering, inc. 252 Granite Street Corona, CA 92879 TEL: 951.493.7155 • TECH: 951.493.7134 E-Mail:[email protected] P/N: 06-80866 ® ®
Sorry, you have been blocked
This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.
What can I do to resolve this?
You can email the site owner to let them know you were blocked. Please include what you were doing when this page came up and the Cloudflare Ray ID found at the bottom of this page.
Cloudflare Ray ID: 812d6b5b58fcb36c • Your IP: Click to reveal 45.84.122.5 • Performance & security by Cloudflare
aFe Power Magnum FORCE 54-13035D Instruction Manual
Compatible devices: 440-401006-N, SCORPION 79-21003L, 51-82722, 46-70270, Scorpion 79-21005L, SCORCHER BLUE 77-83043, 46-70162, 46-71110A.
- Scorpion Instruction manual (UPD: 08 Jul 2023, afe-power/scorpion.pdf) (view)
- 77-83028 Instruction manual (UPD: 18 Dec 2022, afe-power/77-83028.pdf) (view)
- 54-12208 Instruction manual (UPD: 18 Mar 2023, afe-power/54-12208.pdf) (view)
- Scorcher Getting started (UPD: 21 Aug 2023, afe-power/scorcher.pdf) (view)
- Momentum GT Instruction manual (UPD: 03 Feb 2023, afe-power/momentum-gt.pdf) (view)
Instruction Manual (Text Version):
10, 9 Page 10 Step 16: Follow the factory crankcase hose to the rear of the engine 13 . Step 17: Disconnect the hose from its mounting location 14 as shown in Figure 2. Step 18: Once the factory crankcase hose is disconnected, replace it with the supplied aFe POWER hose by slipping the shorter end of the hose at the rear of the engine 15 as shown in Figure 3. Refer to Fi…
7, aFe Power Magnum FORCE 54-13035D aFepower.com Page 7 Refer to Figure D for Steps 10-12 Step 10: Transfer the three factory rubber grommets from the factory airbox to the aFe POWER housing as shown in Figure 1. 8 Step 11: Pre-assemble the aFe POWER housing by inserting the aFe POWER filter. 9 Step 12: Install the supplied trim seal on the aFe POWER housing. 10 Figure D INSTALL 9 8 8 FIGURE 1 8 10 …
9, Step 15: Pre-assemble the aFe POWER intake tube by inserting the supplied rubber grommet and temp sensor fitting. Transfer the temp sensor 12 from the factory tube to the fitting on the aFe POWER tube. Turn the temp sensor clockwise until it locks in place. Refer to Figure F for Step 15 Page 9 Figure F INSTALL 12 …
6, ® Refer to Figure C for Steps 8-9 Step 8: Carefully pull up and remove the trim seal on top of the factory intake scoop, along with 1-2 clips on either side. This helps with removing the factory airbox and installation of the aFe POWER housing. 7 Note: It may help to use a panel popper when pulling the clips. Step 9: Pull the factory intake tube off the throttle body and pull…
4, ® Refer to Figure A for Steps 1-2 Step 1: Pull up on the cover. 1 Step 2: With the 10mm nut driver, remove the factory screw 2 , then carefully pull off the engine cover. Page 4 REMOVAL 1 2 Figure A …
11, Step 19: Install the supplied coupling over the throttle body. Slide one clamp over the throttle body. Tighten the clamp using an 8mm nut driver 16 . Step 20: Slip the other supplied clamp over the other end of the coupling, but do not tighten at this time. 9 Page 11 Refer to Figure H for Steps 19-20 Figure G 11 16 INSTALL Figure H …
2, ® Label Qty. Description Part Number A1 1 Air Filter (Pro DRY S) 21-91146 A2 1 Air Filter (Pro 5R) 24-91146 B 1 Tube 05-5413035B1 C 1 Housing 05-5413023B2 D 1 Plug, Silicone 05-01482 E 1 Fitting, Air Temp. Sensor 05-01454 F 1 Coupling, Silicone, Bellow Reducer 05-01400 G 1 Grommet 03-50167 H 2 Clam…
8, ® Step 13: If desired, install the supplied aFe POWER plug. 11 Step 14: Install the housing assembly into the vehicle. NOTE: Without the plug installed, the aFe POWER intake will capture the maximum air available. More airflow offers more power. Some of this air is picked up from inside the engine compartment and could be warmer air. Warmer air will affect the p…
16, advanced FLOW engineering, inc. 252 Granite Street Corona, CA 92879 TEL: 951.493.7100 • TECH: 951.493.7134 E-Mail:[email protected] P/N: 06-81198 ® …
1, ® advanced FLOW engineering Magnum FORCE Stage-2 Cold Air Intake System Instruction Manual P/N: 54-13035D / 54-13035R Make: Jeep Model: Grand Cherokee (WK2) Year: 2016-2019 Engine: V6-3.6L Make: Dodge Model: Durango Year: 2016-2019 Engine: V6-3.6L …